Layout 1

We use cookies to personalise content and ads, to provide social media features and to analyse traffic. We share info about use of our site with social media, ads and analytics partners. By continuing to browse you are agreeing to use of cookies. See details or close this message.

Page

/31

100%

Specifications	Layout 1
Business section

8www.ittcannon.com/powerlock There are two Line Source connectors for cable attachment, normally referred to as a 400Aand 660

Specifications	Layout 1
Suggested Link Details/Purchase
Content	8www.ittcannon.com/powerlock There are two Line Source connectors for cable attachment, normally referred to as a 400Aand 660Aversion. Both are supplied with a male contact incorporating a rigid IP2X finger proof nose, a slot for the secondary locking pin and a cable gland. The contacts are secured in the housing by using a nylon cotter pin. The 400Aversion has a set screw termination where two threaded set screws are tightened to compress a reduction sleeve which has been fitted to the conductor stranding. The set screw contact is normally used in combination with 120mm2 cable. Smaller cable sections can be terminated by selecting the appropriate reduction sleeves and sliding them on in sequence over the exposed conductor stranding. In combination with these sleeves set screw contacts can handle cables from 25mm2to 120mm2. The 660Aversion has a crimp termination for cable cross sections from 35 mm2to 300mm2cable. The 660Acontact is normally used in combination with 240mm2 cable. It is essential to use the recommended crimp tool and die to ensure a satisfactory crimp. Consult Customer Service for details on pull off loads and mV drop values expected. There are a wide range of cables used in the market to ensure that a satisfactory result is obtained when POWERLOCK connectors are terminated onto to the end of cables, the type and method needs to be evaluated. For more details around termination, please refer to the POWERLOCKTermination Guidewhich is available on www.ittcannon.com. The POWERLOCKTermination Guide provides guidelines on: •how to perform a crimped termination •what type of crimp tools and dies to use with recommendations •how to perform a set screw termination •terminating a threaded post panel type connector •typical test results obtained when terminating connectors onto a range of cables Line Source 400A, Earth Green Line Source 660A, Earth Green Line Source Reliable connections for field installable power distribution systems such as mobile generators.
Navigation	Previous Page / Next Page
Following Datasheets	Powerlock_2010_5 (44 pages) powermodules-1_1 (8 pages) POWERSECTIONGUIDE (1 pages) powerselectionguide (20 pages) PowerSupplyFamily (22 pages) PowerSupplySelectionGuide (1 pages) POWER_CAUTION_1 (1 pages) POWER_INDEX_1 (2 pages) Power_Product_Selector_Brochure (12 pages) POWER_SAFETY_1 (3 pages)
Check in e-portals	World-H-News Products Extensions Partners Automation Jet Parts
Sitemap Folder	group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder