We use cookies to personalise content and ads, to provide social media features and to analyse traffic. We share info about use of our site with social media, ads and analytics partners. By continuing to browse you are agreeing to use of cookies. See details or close this message.

Page

100%

Specifications
Business section

258 Push Type Rocker Type Slide Type Rotary Type Detector Push Slide Rotary Encoders Power Dual-in-line Package Type TACT Swi

Specifications
Outline	Caution
Suggested Link Details/Purchase
Content	258 Push Type Rocker Type Slide Type Rotary Type Detector Push Slide Rotary Encoders Power Dual-in-line Package Type TACT SwitchTM Custom- Products Power Switches Cautions 1.The primary power supply switching is subject to the safety regulations, and the provisions differ by each destination. Consult with us for non-standard use cases. 2.An unstable contact may occur if the switch current is lower than 0.5A. For this case, consult with us. 3.These power switches were produced for alternating current. For direct current, consult with us. 4.Appling load to terminals during soldering under certain conditions may cause deformation and electrical property degradation. 5.Avoid use of water-soluble soldering flux, since it may corrode the switches. 6.When soldering twice, wait until the first soldered portion cools to normal temperature. Continuous heating will deform the external portions, loosen or dislodge terminals, or may deteriorate their electrical characteristics. 7.Before soldering switches with locking mechanism, release the locks. If they are soldered without releasing the locks, the soldering heat may deform the locking mechanism. 8.Be sure to release the locks before removing the knobs. Otherwise, the locking mechanism may be broken. 9.Be sure to use the switch with forced travel positioned as close to the total travel as possible. 10.Tighten the mounting screws by applying the specified torque. Tightening with a larger torque than the specified will result in malfunction or breakage of screws. 11.Corrosive gas if generated by peripheral parts of a set, malfunction such as imperfect contact may occur. Thorough investigation shall be required beforehand. 12.Storage 1Store the products as delivered, at a normal temperature and humidity, without direct sunshine and corrosive gas ambient. Use them at an earliest possible timing, not later than six months upon receipt. 2After breaking the seal, keep the products in a plastic bag to shut out ambient air, store them in the same environment as above, and use them up as soon as possible. 3Do not stack too many switches.
Following Datasheets	POWER_INDEX_1 (2 pages) Power_Product_Selector_Brochure (12 pages) POWER_SAFETY_1 (3 pages) power_supplies (5 pages) power_supplies_complete_cat (278 pages) power_supply_brochure (2 pages) pps_datasheet-1 (13 pages) pp_series (2 pages) PR05-PCB_Brochure_5-20-11 (1 pages) pr36mf1_e (15 pages)
Check in e-portals	World-H-News Products Extensions Partners Automation Jet Parts
Sitemap Folder	group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder

Caution