11-S8E1 hhartenstein

We use cookies to personalise content and ads, to provide social media features and to analyse traffic. We share info about use of our site with social media, ads and analytics partners. By continuing to browse you are agreeing to use of cookies. See details or close this message.

Page

/278

100%

Specifications	11-S8E1 hhartenstein
Business section

Switching Power Supply S8VS13 ■Self-Diagnostics Function Numbers in the following table indicate the number used in Nom

Specifications	11-S8E1 hhartenstein
Outline	Front Page Ordering Information Specifications Engineering Data Operation Dimensions Installation Precautions Contacting Omron
Suggested Link Details/Purchase
Content	Switching Power Supply S8VS13 ■Self-Diagnostics Function Numbers in the following table indicate the number used in Nomenclature on pages 8 and 10. Note:1.External noise is probable as a cause of “-”, “e01”, “e02” and “e03” errors. 2.Operation out of the derating curve area, ventilation error, and incorrect mounting direction are probable as a cause of “h%t” error. 3.If the “h%t” error state continues for more than three hours, the maintenance forecast monitor function becomes invalid. The Yrs output ((12) Maintenance forecast output terminal (Yrs)) will remain OFF (no continuity between (12) Maintenance forecast output terminal (Yrs) and (13) Alarm output common terminal). Replace the power supply if this condition occurs even if the output is correct, as internal parts may be deteriorated. 4.The “h%t” error detection function is only for the S8VS-@@@24A@. (6) Main displayDescriptionOutput statusRestoration methodSetting after restoration Noise detected in voltage or cur- rent No changeAutomatic restorationNo change Overheated(12) Maintenance forecast output ter- minal (Yrs) turns OFF. Automatic restorationNo change Undervoltage alarm set value memory error (11) Undervoltage output terminal (DC LOW) turns OFF. Press and hold the (9) Up Key U or (10) Down Key D for three seconds and check the set value of the corresponding point. The set value must return to the shipment setting Shipment setting or value set in the setting mode again Memory error of alarm set value of maintenance forecast monitor or total run time monitor (12) Maintenance forecast output ter- minal (Yrs) turns OFF or total run time output terminal (kh) turns OFF. Other memory error(11) Undervoltage output terminal (DC LOW) turns OFF. (12) Maintenance forecast output ter- minal (Yrs) turns OFF or total run time output terminal (kh) turns OFF. Turn the AC input OFF then ON again. If the product is not reset, contact the dealer. No change
Navigation	Previous Page / Next Page
Following Datasheets	power_supply_brochure (2 pages) pps_datasheet-1 (13 pages) pp_series (2 pages) PR05-PCB_Brochure_5-20-11 (1 pages) pr36mf1_e (15 pages) pr36mf2_e (15 pages) PRAndersonPower-2 (2 pages) PRArcticSilicon (2 pages) PRCreeXlampXPG (2 pages) precidipcustomdesign (9 pages)
Check in e-portals	World-H-News Products Extensions Partners Automation Jet Parts
Sitemap Folder	group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder

11-S8E1 hhartenstein

11-S8E1 hhartenstein

Front Page Ordering Information Specifications Engineering Data Operation Dimensions Installation Precautions Contacting Omron