SLM ZPACK_2mmHM_5RowCTS_V-P_RA-R

We use cookies to personalise content and ads, to provide social media features and to analyse traffic. We share info about use of our site with social media, ads and analytics partners. By continuing to browse you are agreeing to use of cookies. See details or close this message.

Page

100%

Specifications	SLM ZPACK_2mmHM_5RowCTS_V-P_RA-R_TH.PDF AMP
Business section

SINGLE LINE MODEL DATASHEET Datasheet Filename: ZPACK_2mmHM_5RowCTS_V-P_RA-R_TH.docReviewed By: [CTK] Modeled by: [SC]SPICE F

Specifications	SLM ZPACK_2mmHM_5RowCTS_V-P_RA-R_TH.PDF AMP
Suggested Link Details/Purchase
Content	SINGLE LINE MODEL DATASHEET Datasheet Filename: ZPACK_2mmHM_5RowCTS_V-P_RA-R_TH.docReviewed By: [CTK] Modeled by: [SC]SPICE File: [N/A] Created on 05/21/99 10:24 AM Copyright 1999, AMP IncorporatedACD Internal Form: Form_SLM-DS_1998_0304 RL CCp1Cp2 CONNECTOR Cp1Cp2 Z Tpd CONNECTOR Z-PACK, 2mm CL, HM, 5 Row, Reduced Crosstalk, Vertical Plug to Right Angle Receptacle VALIDATED Well referenced pattern Connector Lumped Constant ModelConnector Distributed Model RowR (mW)L (nH)C (pF)Z (W)Tpd (ps) A125.301.505989 B125.001.805395 Cgroundgroundgroundgroundground D156.102.5049123 E168.002.3059136 Note:(1) The following RLC model is appropriate for edge speeds slower than ten times the highest propagation delay (Tr>=10 * Tpd(highest)). To accommodate faster edge speeds, the lumped model must be divided into two or more RLC sections. For best results, a section’s propagation delay should be 1/10th of the edge speed. (2) The single line inductance and capacitance values are extracted from a specified pattern. The placement and number of ground returns affect the inductance and capacitance of the single line model. (3) The parameters for the Single Line Model are for the connector only without any mounting effects such as plated through holes or pads capacitance (Cp1 and Cp2). The impedance and propagation delay for the connector are calculated as follows: ZL CConnector=()Ω and TpdLCsecConnector=() For an interconnection path model, the mounting effects must be added because the additional capacitance of the pad to ground or plated through hole (Cp1 and Cp2) decrease impedance and increase propagation delay of the interconnection path. The impedance and propagation delay for an interconnection path are calculated as follows: )()21(Ω++=CpCpC LZctInterconne and )()21(secCpCpCLTpdctInterconne++= FOR ADDITIONAL ELECTRICAL MODELING/SIMULATION SUPPORT, CALL 717-986-7824 OR E-MAIL US AT modeling@amp.com
Following Datasheets	ZPACK_2mmHM_5Row_RA-P_V-R_TH (1 pages) ZPACK_2mmHM_5Row_V-P_RA-R_TH (1 pages) ZPACK_2mmHM_8Row_2_V-P_RA-R_TH (1 pages) ZPACK_2mmHM_8Row_V-P_RA-R_TH (1 pages) ZPACK_2mmHM_UPM (1 pages) zqr-3062067B (3 pages) ZR285 (5 pages) ZR4040_2 (5 pages) ZR4040_4 (5 pages) ZR4040_5 (5 pages)
Check in e-portals	World-H-News Products Extensions Partners Automation Jet Parts
Sitemap Folder	group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder

SLM ZPACK_2mmHM_5RowCTS_V-P_RA-R_TH.PDF AMP

SLM ZPACK_2mmHM_5RowCTS_V-P_RA-R_TH.PDF AMP