3pc_bnc_install.pub bobp

We use cookies to personalise content and ads, to provide social media features and to analyse traffic. We share info about use of our site with social media, ads and analytics partners. By continuing to browse you are agreeing to use of cookies. See details or close this message.

Page

100%

Specifications	3pc_bnc_install.pub bobp
Business section

THREE PIECE CRIMP STYLE BNC INSTALLATION INSTRUCTIONS Insert cable into the connector until the center pin is aligned to the

Specifications	3pc_bnc_install.pub bobp
Suggested Link Details/Purchase
Content	THREE PIECE CRIMP STYLE BNC INSTALLATION INSTRUCTIONS Insert cable into the connector until the center pin is aligned to the inner ring. Fold the braid over the connector body and slide the compression ring over the braid as shown. Center pin is aligned with inner ring once cable is in place Prepare the cable according to step 1 to achieve the proper braid exposure and center conductor length. Slightly flair the braid away from the dielectric. Twist the foil tightly against the dielectric and verify there are no loose braids or foil touch- ing the center conductor. Connector P/N: 1694ABHD3, 1505ABHD3, 1855ABHD3, 179DTBHD3 Compression tool: BB3PHCT Preparation tool: BB3PST Step 1 Tool setup Step 3 Step 4 Connector color code: Green - 1694A / 1695A Red - 1505A / 1506A Purple - 1855A Yellow - 179DT Recess for purple and yellow connectors Recess for red connectors Recess for green connectors Recess to crimp center pin on all versions Insert the center pin onto the center conductor and crimp in place with the tool Step 2 The BB3PHCT hex crimp tool is configured with one die set for use with all Belden three piece hex connectors. Refer to the tool instructions for further details. The BB3PST preparation tool includes all required components to prepare cables used with the Belden three piece hex connectors. Refer to the tool instruction sheet for further details. With the connector fully installed on the cable, insert the compression ring into the proper tool recess. Position the die so the hex crimp will be centered on the ring. Fully close the tool handle until the ratchet mechanism allows the tool to open. Once completed, the connector has been terminated as shown below. Center pin Compression ring Crimp area
Following Datasheets	ThreePhaseXFMR (1 pages) ThreeState_Bibuf_AN (4 pages) ThreeState_BoardTest_AN (2 pages) threew (1 pages) thrmobnd1500hrdner (4 pages) thrmobnd1500resin (4 pages) thrmobnd1600hrdner (4 pages) thrmobnd1600resin (4 pages) thrmtant (9 pages) Through-Hole-Printing (7 pages)
Check in e-portals	World-H-News Products Extensions Partners Automation Jet Parts
Sitemap Folder	group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder