N2-bus.bk

We use cookies to personalise content and ads, to provide social media features and to analyse traffic. We share info about use of our site with social media, ads and analytics partners. By continuing to browse you are agreeing to use of cookies. See details or close this message.

Page

/44

100%

Specifications	N2-bus.bk
Business section

Chapter 4 – Programming ACS/ACH 400 Direct N2 Bus Interface4-7 8 PID-CONT D-TIMENo setup is necessary. 9 PID-CONT D-FIL

Specifications	N2-bus.bk
Outline	Safety Instructions Overview Warnings and Notes Warnings Notes Chapter 4 – Programming Programming of the Drive Supported Features Analog Input Binary Input Analog Output Binary Output Appendix A – I/O Point List Parameters Chapter 2 – Overview of the N2 Connection Introduction Metasys Integration Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type DDL File Device Type Chapter 4 – Programming Chapter 5 – Fault Tracing Appendix A – I/O Point List Appendix B – DDL File for NCU
Suggested Link Details/Purchase
Content	Chapter 4 – Programming ACS/ACH 400 Direct N2 Bus Interface4-7 8 PID-CONT D-TIMENo setup is necessary. 9 PID-CONT D-FILTERNo setup is necessary. 10 COMMAND AO 1Set the parameter 1501 AO CONTENT to 133 (SERIAL LINK DATA 3) and set the parameter 1503 AO CONTENT MAX to 255. Binary OutputsBelow is a list of all the analog output points for the N2 Bus interface for the ACS/ACH400 drive. 1 STOP/STARTSet Parameter 1001 EXT1 COMMANDS to COMM, when using Reference R1. Set Parameter 1002 EXT2 COMMANDS to COMM, when using Reference R2. When this point is overridden to 0, the drive will ramp to stop. Use the Binary Output 4 RUN ENABLE for stopping the drive by coast. 2 FORWARD/REVERSESet Parameter 1003 to REQUEST. Also, depending on the selected reference, setup the following Parameter: •Set Parameter 1103 EXT REF1 SELECT to COMM, when using Reference R1. •Set Parameter 1104 EXT REF2 SELECT to COMM, when using Reference R2. 3 PANEL LOCKNo setup is necessary. 4 RUN ENABLENo setup is necessary. Note that this point must always be set to 1 to start the drive. If Binary Output 1 STOP/START is kept high and this point is overridden to 0, the drive will coast to stop. 5 REF1/REF2Set Parameter 1102 EXT1/EXT2 SEL to COMM. 6 FAULT RESETSet Parameter 1604 FAULT RESET SEL to COMM. 7 COMMAND RO 1Set Parameter 1401 RELAY OUTPUT 1 to 7 “SUPERV1 OVER”, SET Parameter 3201 SUPERV 1 PARAM to 131 “SERIAL LINK DATA 1” and set Parameter 3203 SUPERV 1 LIM HI to 1.
Navigation	Previous Page / Next Page
Following Datasheets	H600en_Rev01 (2 pages) H601en_Rev01 (2 pages) H608en (2 pages) H609en (2 pages) H610en (2 pages) H611en (2 pages) H612en_Rev01 (2 pages) H613en (2 pages) H614en (2 pages) H615en (2 pages)
Check in e-portals	World-H-News Products Extensions Partners Automation Jet Parts
Sitemap Folder	group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder