| Specifications | |
| Business section |
|
|
|
|
|
||||||||||||||||||||||||||||||||||
|
|
|
|
|
||||||||||||||||||||||||||||||||||
| Specifications | |
| Business section |
| Specifications | |
| Suggested Link Details/Purchase | |
| Content | A A.1Parameter list A-741 Siemens AG 2003 All rights reservedSIMODRIVE POSMO SI/CD/CA User Manual (POS3) – 07.03 Edition 1256:8 Ramp–function generator ramp–up time MinStandardMaxUnitData typeEffective 0.02.0600.0sFloating Pointimmed.(ARM) 0.00.0600.0sFloating Pointimmed.(SRM SLM) During ramp–up, the setpoint is increased from zero to the maximum permissible actual speed. Note: Max. permissible actual speed for synchronous motors: Minimum from 1.1 (1.05 from SW 7.1 with ”SIMODRIVE 611 universal HR”, resolver) x P1400 and P1147 Max. permissible actual speed for induction motors: Minimum from P1146 and P1147 refer to the index entry ”Ramp–function generator”. 1257:8 Ramp–function generator ramp–down time MinStandardMaxUnitData typeEffective 0.02.0600.0sFloating Pointimmed.(ARM) 0.00.0600.0sFloating Pointimmed.(SRM SLM) During ramp–down, the setpoint is reduced from the maximum permissible actual speed to zero. Note: Max. permissible actual speed for synchronous motors: Minimum from 1.1 (1.05 from SW 7.1 with ”SIMODRIVE 611 universal HR”, resolver) x P1400 and P1147 Max. permissible actual speed for induction motors: Minimum from P1146 and P1147 refer to the index entry ”Ramp–function generator”. 1259 Torque/power reduction mot./gen. (ARM SRM)(–> 4.1) Force/power reduction mot./gen. (SLM) MinStandardMaxUnitData typeEffective 003HexUnsigned16immed. . defines if the torque/power de–rating or force/power de–rating depends on whether the drive is motoring/generating. Bit 0Torque / power reduction, only when motoring Bit 0 = 1Reduction is only effective when motoring Bit 0 = 0Reduction is effective when motoring and regenerating Bit 1Limiting, motoring/regenerating dependent on Nset Bit 1 = 1The torque limits when motoring are used if the product of torque and speed set- point is positive and the speed setpoint is not equal to 0 Bit 1 = 0The torque limits when motoring are used if the product of torque and speed actual value is positive or the absolute speed actual value is less than 10 RPM Note: Refer under index entry ”Torque/power reduction” 1262 i2t time in limiting MinStandardMaxUnitData typeEffective –––sFloating PointRO . for the i2t power section limit, this is used to display the time during which the power section is being limited. Note: The parameter is reset for value overflow and for POWER ON. refer to the index entry ”i2t power section limiting” A Lists03.0107.03 |
| Navigation | Previous Page / Next Page |
| Following Datasheets | manual_s7_200_2004_cz (534 pages) manual_s7_200_2004_en (534 pages) manual_s7_200_2005_en (534 pages) mapa_cr (1 pages) mapa_praha (1 pages) MCC_programming_en (454 pages) micro_automation_set_testcode_01_en (6 pages) micro_automation_set_testcode_02_en (5 pages) micro_automation_set_testcode_03_en (5 pages) micro_automation_set_testcode_04_en (5 pages) |
Check in e-portals |
World-H-News Products Extensions Partners Automation Jet Parts |
| Sitemap Folder | group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder |
