We use cookies to personalise content and ads, to provide social media features and to analyse traffic. We share info about use of our site with social media, ads and analytics partners. By continuing to browse you are agreeing to use of cookies. See details or close this message.

Page

/828

100%

Specifications
Business section

6 6.9Motor changeover for induction motors (only POSMO CD/CA) 6-504 Siemens AG 2003 All rights reservedSIMODRIVE POSMO SI/CD/

Specifications
Suggested Link Details/Purchase
Content	6 6.9Motor changeover for induction motors (only POSMO CD/CA) 6-504 Siemens AG 2003 All rights reservedSIMODRIVE POSMO SI/CD/CA User Manual (POS3) – 07.03 Edition 6.9.5Parameters for the motor changeover The following parameters are used for motor changeover: Table 6-49Parameters for motor changeover Parameters No.DescriptionMinStandardMaxUnitsEffective 1013Enable motor changeover (ARM)003–PO . the motor changeover is enabled or the type of motor changeover is set. ValueDescription 0Motor changeover inhibited 1Motor changeover with pulse cancellation 2Motor changeover without pulse cancellation (data set changeover) 3Motor changeover with speed thresholds (P1247, P1248) Note: It is only possible to enable motor changeover in the “speed/torque setpoint” mode (P0700=1). 1247Speed threshold, changeover motor 1/2 (ARM) 100.0100 000.0100 000.0RPMImmedia- tely 1248Speed threshold, changeover motor 3/4 (ARM) 100.0100 000.0100 000.0RPMImmedia- tely . the speed thresholds for the motor changeover are defined with the speed threshold (P1013 = 3). P1247: Below P1247 minus 5% hysteresis, the first motor data set is selected (P1xxx). Above P1247 plus 5% hysteresis, the second motor data set is selected (P2xxx). P1248: Below P1248 minus 5% hysteresis, the third motor data set is selected (P3xxx). Above P1248 plus 5% hysteresis, the fourth motor data set is selected (P4xxx). Motor data setMotor data set P1xxxP1247P2xxx P3xxxP1248P4xxx n5 %5 % Parameter overview 03.016 Description of the Functions
Navigation	Previous Page / Next Page
Following Datasheets	manual_s7_200_2004_cz (534 pages) manual_s7_200_2004_en (534 pages) manual_s7_200_2005_en (534 pages) mapa_cr (1 pages) mapa_praha (1 pages) MCC_programming_en (454 pages) micro_automation_set_testcode_01_en (6 pages) micro_automation_set_testcode_02_en (5 pages) micro_automation_set_testcode_03_en (5 pages) micro_automation_set_testcode_04_en (5 pages)
Check in e-portals	World-H-News Products Extensions Partners Automation Jet Parts
Sitemap Folder	group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder