We use cookies to personalise content and ads, to provide social media features and to analyse traffic. We share info about use of our site with social media, ads and analytics partners. By continuing to browse you are agreeing to use of cookies. See details or close this message.

Page

/828

100%

Specifications
Business section

6 6.2Positioning mode (P0700 = 3) 6-391 Siemens AG 2003 All rights reservedSIMODRIVE POSMO SI/CD/CA User Manual (POS3) –

Specifications
Suggested Link Details/Purchase
Content	6 6.2Positioning mode (P0700 = 3) 6-391 Siemens AG 2003 All rights reservedSIMODRIVE POSMO SI/CD/CA User Manual (POS3) – 07.03 Edition Table 6-33Parameters for programming traversing blocks, continued No.EffectiveUnitsMaxStandardMinName The position actual value is written into P0026 (position actual value external block change) when an edge is identified at the “External block change” input signal. BlockPos.VelocityCommandPositioning modeBlock change enable 0100100POSITIONINGABSOLUTECONTINUE FLYING 120050POSITIONINGABSOLUTECONTINUE EXTERNAL 2300100POSITIONINGABSOLUTEEND 10 0 v t Example: Programming 3 traversing blocks Block 1 with CONTINUE EXTERNAL 0 1 signal 0 signal Input signal ”External block change” Block 0 Block 1Block 2 Block 1, if there is no edge P0110 = 0 P0110 = 1 Position actual value in P0026 Note: Refer to the index entry “Input signal – external block change”. 0087:64 Xxxx Spindle positioning (from SW 5.1) For the “Spindle positioning” function, the target position is programmed in P0081 or is trans- ferred via PROFIBUS–DP. Note: Refer under the index entry “Spindle positioning” 03.016 Description of the Functions02.02
Navigation	Previous Page / Next Page
Following Datasheets	manual_s7_200_2004_cz (534 pages) manual_s7_200_2004_en (534 pages) manual_s7_200_2005_en (534 pages) mapa_cr (1 pages) mapa_praha (1 pages) MCC_programming_en (454 pages) micro_automation_set_testcode_01_en (6 pages) micro_automation_set_testcode_02_en (5 pages) micro_automation_set_testcode_03_en (5 pages) micro_automation_set_testcode_04_en (5 pages)
Check in e-portals	World-H-News Products Extensions Partners Automation Jet Parts
Sitemap Folder	group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder