Specifications | Manual SIMATIC LOGO! Manual A5E00228550-01, Edition 05/2003 A&D AS SM ID |
Business section |

Specifications | Manual SIMATIC LOGO! Manual A5E00228550-01, Edition 05/2003 A&D AS SM ID |
Business section |
Specifications | Manual SIMATIC LOGO! Manual A5E00228550-01, Edition 05/2003 A&D AS SM ID |
Outline | Title Preface Contents Preface i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Getting started with LOGO! 1 . . . . . . . 2 LOGO! installation and wiring 11 . . . . . 3 Programming LOGO! 37 . . . . . . . . . . . . 4 LOGO! functions 89 . . . . . . . . . . . . . . . . . 5 Configuring LOGO! 193 . . . . . . . . . . . . . . . 6 LOGO! program module (card) 203 . . . . 7 LOGO! Software 215 . . . . . . . . . . . . . . . . . 8 Applications 221 . . . . . . . . . . . . . . . . . . . . . Appendix A Technical data 259 . . . . . . . . . . . . . . . . . . . B Determining the cycle time 283 . . . . . . . . C LOGO! without display 285 . . . . . . . . . . . D LOGO! menu structure 289 . . . . . . . . . . . E Order numbers 291 . . . . . . . . . . . . . . . . . . . F Abbreviations 293 . . . . . . . . . . . . . . . . . . . . Index 295 . . . . . . . . . . . . . . . . . . . . . . . . . . . . F Abbreviations Index A B C D E F G H I L M N O P R S T U W X Y Z |
Suggested Link Details/Purchase | |
Content | 11 LOGO! ManualA5E00228550-01 2LOGO! installation and wiring General guidelines Please note the following guidelines for the installation and wiring of your LOGO! : Always ensure that the wiring of your LOGO! is com- pliant with current rules and standards. Also, conform with all national and regional regulations when you install and operate the devices. For information on stan- dards and regulations that apply to your specific case, contact your local authorities. Always use cables with an appropriate conductor cross- sections for the relevant current. You can wire the LOGO! with cable conductor cross-sections from 1.5 mm2 to 2.5 mm2; see Chapter 2.3. Do not exceed the screw torque of the terminals. The maximum torque is: 0.5N/m, see Chapter 2.3. Keep the cabling as short as possible. If longer cables are necessary, you should use shielded versions. You should always route your cables in pairs: i.e. one neutral conductor plus one phase conductor or signal line. Always keep separate: –The AC wiring –High-voltage DC circuits with high-frequency switch- ing cycles –Low-voltage signal wiring. Ensure that the wires are installed with an appropriate strain relief. Provide a suitable lightning surge arrester for cables installed in relevant areas of hazard. |
Navigation | Previous Page / Next Page |
Following Datasheets | manual_logo_am2_pt100_2001_en (6 pages) manual_posmo_a_08-2003_en (270 pages) manual_posmo_cd_ca_si_07-2003_en (828 pages) manual_s7_200_2004_cz (534 pages) manual_s7_200_2004_en (534 pages) manual_s7_200_2005_en (534 pages) mapa_cr (1 pages) mapa_praha (1 pages) MCC_programming_en (454 pages) micro_automation_set_testcode_01_en (6 pages) |
Check in e-portals![]() |
World-H-News Products Extensions Partners Automation Jet Parts |
Sitemap Folder | group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder |