We use cookies to personalise content and ads, to provide social media features and to analyse traffic. We share info about use of our site with social media, ads and analytics partners. By continuing to browse you are agreeing to use of cookies. See details or close this message.

Page

/828

100%

Specifications
Business section

4 03.01 4.6Induction motor operation with induction motor (only POSMO CD/CA) 4-153 Siemens AG 2003 All rights reservedSIMODRI

Specifications
Suggested Link Details/Purchase
Content	4 03.01 4.6Induction motor operation with induction motor (only POSMO CD/CA) 4-153 Siemens AG 2003 All rights reservedSIMODRIVE POSMO SI/CD/CA User Manual (POS3) – 07.03 Edition Determining the moment of inertia. The moment of inertia is set, so that when accelerating to the maxi- mum speed, no I component is set in the speed controller. Note This step should be made with a coupled load, if a significant load mo- ment of inertia will be present in actual operation. During the identification runs, the total moment of inertia (P1117 + P1123:8) is taken into account and corrected in P1117. The commissioning engineer must make the appropriate distribution between P1117 and P1123:8 (parameter set independent and depen- dent). ! Danger The motor is accelerated, with a positive rotating field direction, to the maximum speed along the torque limit. The step is executed as follows: 1.step, select: P1083 = 4 2.step, start: P1084 = 1 –P1084 = 1The step has been started and is running It can be canceled with P1084 = 0. –P1084 = 1/0The step was successfully completed –P1084 = –xThe step was canceled with fault–x (refer to P1084 in Chapter A.1) Start again after the fault has been removed. The following parameters are calculated/written into: P1117 The following parameters are used for IM operation (encoderless oper- ation): Commissioning step 4 (this is not carried out for auto commissio- ning in MSD oper- ation) Executing step 4 Changed parameters Parameter overview 4 Start-Up
Navigation	Previous Page / Next Page
Following Datasheets	manual_s7_200_2004_cz (534 pages) manual_s7_200_2004_en (534 pages) manual_s7_200_2005_en (534 pages) mapa_cr (1 pages) mapa_praha (1 pages) MCC_programming_en (454 pages) micro_automation_set_testcode_01_en (6 pages) micro_automation_set_testcode_02_en (5 pages) micro_automation_set_testcode_03_en (5 pages) micro_automation_set_testcode_04_en (5 pages)
Check in e-portals	World-H-News Products Extensions Partners Automation Jet Parts
Sitemap Folder	group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder