
Specifications | |
Business section |
Specifications | |
Suggested Link Details/Purchase | |
Content | Design and specifi cations are each subject to change without notice. Ask factory for the current technical specifi cations before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Fixed Inductors (Chip Inductors) – 129 – Precautions for use 1. Operation range and environments 1 These products are designed and manufactured for general and stan dard use in general elec tron ic equipment (e.g. AV equipment, home electric ap pli anc es, offi ce equipment, information and com mu ni ca tion equipment) 2 These products are not intended for use in the following special conditions. Be fore using the products, care ful ly check the effects on their quality and performance, and determine whether or not they can be used. • In liquid, such as water, oil, chemicals, or organic solvent • In direct sunlight, outdoors, or in dust • In salty air or air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2 • In an environment where these products cause dew condensation 2.Handling 1Do not bring magnets or magnetized materials close to the product. The infl uence of their magnetic fi eld can change the inductance value. 2Do not apply strong mechanical shocks by either dropping or collision with other parts. Excessive schock can damage the part. 3.Land pattern design 1Please refer to the recommended land pattern for each type shown on the datasheet. 2Avoid placing the chip inductor on any metal pattern except the recommended land pattern because a drop of Q and mutual conductance may occur. 3In case of fl ow soldering, venting of soldering fl ux gases should be made for high density assemblies to get a good solder connection. 4In case of refl ow soldering, consider the layout because taller components close to chip inductor tend to block thermal conduction. 4. Mounting 1In general, magnetic and electric characteristics of ferrite cores can be changed by applying excessively strong force. Placement force should not exceed 20 N. 2Do not bend or twist the PWB after mounting the part. 5. Cleaning 1Do not use acid or alkali agents. Some cleaning solvents may damage the part. Confi rm by testing the reliability in advance of mass production. 2If Ultrasonic cleaning is used, please confi rm the reliability in advance. It is possible that combined resonance of component and PWB and cavitation can cause an abnormal vibration mode to exist causing damage. 6.Caution about applying excessive current The rated current is defi ned as the smaller value of either the current value when the inductance drops 10 % down from the initial point or the current value when the average temperature of coil inside rises 20 °C up from the initial point. Do not operate product over the specifi c max. current. Safety Precautions (Common precautions for Chip Inductors) • When using our products, no matter what sort of equipment they might be used for, be sure to make a written agreement on the specifi cations with us in advance. The design and specifi cations in this catalog are subject to change without prior notice. • Do not use the products beyond the specifi cations described in this catalog. • This catalog explains the quality and performance of the products as individual components. Be fore use, check and evaluate their operations when installed in your products. • Install the following systems for a failsafe design to ensure safety if these products are to be used in equip ment where a defect in these products may cause the loss of human life or other signifi cant damage, such as damage to vehicles (au to mo bile, train, vessel), traffi c lights, medical equipment, aerospace equipment, elec tric heating ap pli anc es, com bus tion/gas equipment, rotating equipment, and disaster/crime prevention equip ment. ✽ Systems equipped with a protection circuit and a protection device ✽ Systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault <Package markings> Package markings include the product number, quantity, and country of origin. In principle, the country of origin should be indicated in English. Sep. 201000 |
Suggested Link Details/Purchase | |
Following Datasheets | AGB0000CE10 (4 pages) AGB0000CE2 (5 pages) AGB0000PE2 (1 pages) AGB0000PE28 (2 pages) agenda0508 (1 pages) agenda110510 (1 pages) agenda_12_13_2006 (1 pages) aggseries (7 pages) AGI0000CE1 (5 pages) AGL0000CE1-1 (2 pages) |
Check in e-portals![]() |
World-H-News Products Extensions Partners Automation Jet Parts |
Sitemap Folder | group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder |