Agenda of the Laws and Regulations Committee Ken Butcher

We use cookies to personalise content and ads, to provide social media features and to analyse traffic. We share info about use of our site with social media, ads and analytics partners. By continuing to browse you are agreeing to use of cookies. See details or close this message.

Page

/18

100%

Specifications	Agenda of the Laws and Regulations Committee Ken Butcher
Business section

NTEP Committee 2011 Final Report NTEP - 1 Report of the National Type Evaluation Program (NTEP) Committee Randy Jennings, Cha

Specifications	Agenda of the Laws and Regulations Committee Ken Butcher
Outline	Table of Contents - Annual Report of the 96th NCWM NTEP 2011 Final Report 500 INTRODUCTION Table of Contents 500-1 I Mutual Recognition Arrangement (MRA) 500-2 I Mutual Acceptance Arrangement (MAA) 500-3 I NTEP Participating Laboratories and Evaluations Reports 500-4 I National Type Evaluation Technical Committee (NTETC) Sector Reports 500-5 I Conformity Assessment Program 500-6 I NTEP Contingency 500-7 I Publication 14 – NTEP Administrative Policy
Suggested Link Details/Purchase
Content	NTEP Committee 2011 Final Report NTEP - 1 Report of the National Type Evaluation Program (NTEP) Committee Randy Jennings, Chairman Executive Assistant Tennessee Department of Agriculture Reference Key Number 500 INTRODUCTION The National Type Evaluation Program (NTEP) Committee (hereinafter referred to as “Committee”) submits its report for consideration by the 96th National Conference on Weights and Measures (NCWM). This consists of the Interim Report presented in NCWM Publication 16 as amended in the Addendum Sheets issued during the Annual Meeting that was held July 17 - 21, 2011, in Missoula, Montana. The Committee considered communications received prior to and during the 96th Annual Meeting that are noted in this report. Table A identifies the agenda and appendix items. The agenda items are listed by Reference Key Number, Item Title, and Page Number. The item numbers are those assigned in the Committee’s Interim Meeting Agenda. A Voting item is indicated with a “V” after the item number or, if the item was part of the consent calendar, by the suffix “VC.” An item marked with an “I” after the reference key number is an Informational item. An item marked with a “W” was Withdrawn by the Committee and generally will be referred to the regional weights and measures associations because it either needs additional development, analysis, and input or does not have sufficient Committee support to bring it before the NCWM. Table B contains provides a glossary of acronyms used in this report, and Table C provides a summary of the results of the voting on the Committee’s items and the report in entirety. This report contains many recommendations to revise or amend National Conference on Weights and Measures (NCWM) Publication 14, Administrative Procedures, Technical Policy, Checklists, and Test Procedures or other documents. Proposed revisions to the publication(s) are shown in bold face print by striking out information to be deleted and underlining information to be added. Requirements that are proposed to be nonretroactive are printed in italics. Note: The policy of the National Institute of Standards and Technology (NIST) is to use metric units of measurement in all of its publications; however, recommendations received by the NCWM technical committees have been printed in this publication as they were submitted and may, therefore, contain references to inch-pound units. Table A Index to Reference Key Items Reference Key Number Title of Item Page 500 INTRODUCTION . NTEP - 1 500-1 I Mutual Recognition Arrangement (MRA) . NTEP - 3 500-2 I Mutual Acceptance Arrangement (MAA) . NTEP - 4 500-3 I NTEP Participating Laboratories and Evaluations Reports . NTEP - 6 500-4 I National Type Evaluation Technical Committee (NTETC) Sector Reports . NTEP - 10 500-5 I Conformity Assessment Program . NTEP - 11 500-6 I NTEP Contingency . NTEP - 15 500-7 I Publication 14 – NTEP Administrative Policy . NTEP - 16
Navigation	Previous Page / Next Page
Suggested Link Details/Purchase

Following Datasheets	10-ntep-app-a-09-annual-final (20 pages) 10-ntep-app-a-11-pub15-final (28 pages) 10-ntep-app-a-grain-10-annual-final (30 pages) 10-ntep-app-b-09-annual-final (38 pages) 10-ntep-app-b-11-annual-final (46 pages) 10-ntep-app-b-11-pub15-final (46 pages) 10-ntep-app-b-meas-10-annual-final (96 pages) 10-ntep-app-c-09-annual-final (51 pages) 10-ntep-app-c-11-annual-final (30 pages) 10-ntep-app-c-11-pub15-final (30 pages)
Check in e-portals	World-H-News Products Extensions Partners Automation Jet Parts
Sitemap Folder	group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder