MB452-usermanual

We use cookies to personalise content and ads, to provide social media features and to analyse traffic. We share info about use of our site with social media, ads and analytics partners. By continuing to browse you are agreeing to use of cookies. See details or close this message.

Page

100%

Specifications	MB452-usermanual
Business section

Default setting : 50.0 (122.0 )● b. HUTR Display To enter the HUTR mode. The hour signal is displayed as below: 3-2. HD

Specifications	MB452-usermanual
Suggested Link Details/Purchase
Content	Default setting : 50.0 (122.0 )● b. HUTR Display To enter the HUTR mode. The hour signal is displayed as below: 3-2. HDD Access Display: If HDD is reading or writing, HDD access signal displays the below: 3-3. ● Overheating Alarm:If the alarm temperature is set to 50.0 (122.0 ) and the detected temperature is higher the LCD displays the following: HDD access and Fan signals are displayed. Temperature and alarm buzzer signals will continuously flash. ● 3-4. ● If setting temperature at 55.0 (131.0 ), the LCD will display the following: Press hold the SET button for more than 3 seconds, and the alarm buzzer will sound BEEP twice as confirmed choice.If sound BEEP is less than twice, it is not a confirmed choice. Remark: If LCD screen does not return to Main Display, stop operation for 15 seconds, the LCD will then automatically return to the Main Display and the original temperature detection setting will be cancelled. c. 3-5. ● Fan Fail Alarm If the fan fails or is disconnected, the LCD displays the following: HDD access signal is displayed. Fan and alarm buzzer signals will continuously flash. Remark: Buzzer and alarm symbol are disable by pressing any buttons located at the front panel. ● /°F°C °C°F °F°C°C°F fter confirming themode you enter the Temperaturedetectionsetting mode. The LCD screen flashes thefollowin A g Pull the active handle of the tray until segment C (refer to 2-1-8).Press the adjoining section of the active handle and handle pulling the handle to remove the tray from the external housing. Push the release latch to remove the top cover by sliding backwards. 4-4.Connect the interface and power connectors 4-3.Insert the tray into the external housing andclose the handle.Use the miniature key rovided tosecure the handle.( refer to 2-5 ) UKGF(IDE HDD)MKGF(SATA HDD) HDDHDD <4.>Installation Guide 4-1. Place the HDD inside the tray and connect the interface and power connectors to the HDD. Secure the HDD to the tray using the screws provided (check the accessory bag). Place the top cover back to the tray. Slide forward to secure. 4-2. p to the external housing and to the source. <1.>Contents Description <2.>Appearance e-SATA cable (MB452MKGF) crimping SATA Front Panel Description 1. LCD screen display 2. SET button 3. UP button 4. Down button 5. Cartridge frame 6. Handle 7. Key lock LCD Screen Symbol Description 1. Hard drive access 2. HUTR indicator 3. SET selector 4. Numeric indicator 5. MASTER display 6. SLAVE display 7. Up selector Default Setting ItemDefault setting Temperature detect MASTER/SLAVE Display HUTR0 SLAVE 50.0 C (122.0 F) 2-2.▲2-1. A BC 123456789101211131415 Whole Unit (External Removable Hard Drive Rack) User manualExternal Power Adapter AC/DC USB Converter (A type to B type) cable 8. Active handle 8. Day indicator 9. Decimal indicator 10. Degrees indicator 11. Hour indicator 12. Down selector 13. Temperature status 14. Fan status 15. Alarm Note: HUTR (HDD Usage Time Record) A: Protect the hidden key lock B: Enable the handle to pivot and allow the handle to clamp C: Enable to pull out the cartridge #6-32 4 x HDD screws 2 x keys Foldable foot stand ● HDD mode : SLAVE(Default Setting) (▼) button,the LCD displays shows alternating the following modes: (▲) or →HUTR Display When power is turned on,the LCD screen displays the following: ● Press the Temperature Detection Setting ● Surrounding : temperature if at 30.6 Temperature Detection andSettings From main display, press SET button to enter temperature setting mode and display the following : ● Press button or button to switch the→ → ● Press SET button to confirm your choice ▲Power port E: Power Off / Locked F: Power Off / Unlocked Segment Key Lock Description D: Power On / Locked ▲SATA port ▲USB 2.0 port 2-3-1. 2-4. 2-4.◇ D E F 2-5.◇ 3-1. <3.>Function Settings and Operation a. °F °C °F°C/ /°F°C °C°C 2-3-2. 2-3-3. 3 (▲)(▼) e-SATA 2-3-12-3-22-3-3
Suggested Link Details/Purchase

Following Datasheets	MB452MK_USERMAUAL3 (1 pages) MB452UKGF_usermanul (2 pages) MB453-4-5_Revised (1 pages) MB453-usermanual (1 pages) MB453IPF_Manual (1 pages) MB454-usermanual (1 pages) MB455-usermanual (1 pages) MB559UEA-US-1 (1 pages) MB559UEA-US-2 (1 pages) MB561S-4S-1 (1 pages)
Check in e-portals	World-H-News Products Extensions Partners Automation Jet Parts
Sitemap Folder	group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder