| Specifications | document |
| Business section |
|
|
|
|
|
||||||||||||||||||||||||||||||||||
|
|
|
|
|
||||||||||||||||||||||||||||||||||
| Specifications | document |
| Business section |
| Specifications | document |
| Suggested Link Details/Purchase | |
| Content | Appendix B packaging - ceramic chip capacitors carrier tape specifications Notes: 1.A0, B0 and K0are determined by the max. dimensions to the ends of the terminals extending from the components body and/or the body of the component. The clearance between the end of the terminals of the body of the components to the sides and depth of the cavity (A0, B0and K0) must be within .002 (0.05)mm min. and .020 (0.50)mm max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see examples A & B). 2.Tape with components shall pass around radius R without damage. The minimum trailer length (Note 2 Fig. 3) may require additional length to provide R min. for .472 (12)mm embossed tape for reels with hub diameters approaching N min. (Table 4). 3.G1dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed cavities or to the edge of the cavity whichever is less. 4.G2dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less. 5.The embossed hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 6. B1dimension is a reference dimension for tape feeder clearance only. Tape SizeConstantD0EP0P2T Max.T1G1G2 Carrier Tape Dimensions Dimensions inches (mm) Tape SizeVariableB1Max.See note 6D1Min.See note 5FP1R Min. See note 2T2WA0B0K0 Dimensions inches (mm) 8mm,.059.069 ± .004.157 ± .004.079 ± .002.024.004.030.030 12mm(1.5 )(1.75 ±0.10)(4.0 ± 0.10)(2.0 ± 0.05)(0.600)(0.10) Max.(0.75) Min.(0.75) Min.See note 3See note 4 ±.004-0.0 ±0.10-0.0 269KOA Speer Electronics, Inc.• 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.1/03/11 appendix & add. information 8mm .179.039.138 ± .002.157 ± .004.984.098.315See note 1(4.55)(1.0)(3.5 ± 0.05)(4.0 ± 0.10)(25)(2.5 Max.)(8.0 ) 12mm .323.059.217 ± .002.157 ± .0041.181.256.472 ± .012See note 1(8.2)(1.5)(5.5 ± 0.05)(4.0 ± 0.10)(30)(6.5 Max.)(12.0 ± .30) 12mm .179.039.138 ± .002.079 ± .004.984.098.315See note 11/2 Pitch(4.55)(1.0)(3.5 ± 0.05)(2.0 ± 0.10)(25)(2.5 Max.)(8.0 ) 12mm .323.059.217 ± .002.315 ± .0041.181.256.472 ± .012See note 1Double Pitch(8.2)(1.5)(5.5 ± 0.05)(8.0 ± 0.10)(30)(6.5 Max.)(12.0 ± .30) ± .012- .004± 0.3- 0.1 Bottom covertape T1 T Top covertape D0P2 A0 B0 P0 10 pitches cumulative tolerance on tape±0.008 (±0.2) Center linesof cavityUser direction of feed Cavity size,see note 1 G1 E F W G2T1 P1 Top View Example “D” 20° Maximum Component Rotation Typical componentcavity center line Typical component center line BO AO Maximum Component Rotation Side or Front Sectional ViewExample “C” 20° T Punched paper tape 8 & 12mmNotes: 1.A0, B0 and T are determined by the max. dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The clearance between the ends of the terminals or body of the components to the sides and depth of the cavity (A0, B0and T) must be within .002 (0.05) mm min. and .020 (0.50) mm max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see examples C & D). 2.Tape with components shall pass around radius R without damage. 3.043 (1.1) mm base tape and .063 (1.6) mm max. for non-paper base compositions. Tape SizeConstantD0EP0P2T1G1G2R Min. Carrier Tape Dimensions Dimensions inches (mm) 8mm .059.069 ± .004.157 ± .004.079 ± .002.004.030.030.984 12mm(1.5 )(1.75 ±0.10)(4.0 ± 0.10)(2.0 ± 0.05)(0.10)(0.75)(0.75)(25)Max.Min.Min.See note 2 Tape SizeVariableP1FWA0B0T Dimensions inches (mm) 8mm .157 ± .004.138 ± .002.315(4.0 ± 0.10)(3.5 ± 0.05)(8.0 ) 12mm .157 ± .004.217 ± .002.472 ± .012(4.0 ± .010)(5.5 ± 0.05)(12.0 ± 0.3)See note 1See note 38mm .079 ± .004.138 ± .002.3151/2 Pitch(2.0 ± 0.10)(3.5 ± 0.05)(8.0 ) 12mm .315 ± .004.217 ± .002.472 ± .012Double Pitch(8.0 ± .010)(5.5 ± 0.05)(12.0 ± 0.3) ±.004-.000 ±0.1-0.0 ±.012-.004 ±0.3-0.1 ±.012-.004 ±0.3-0.1 ± .012- .004± 0.3- 0.1 |
| Navigation | Previous Page / Next Page |
| Suggested Link Details/Purchase | |
| Following Datasheets | Appendix_C (10 pages) Appendix_D (2 pages) Appendix_E (4 pages) appguide0104 (1 pages) appguide0204 (1 pages) appguide0205-1 (1 pages) appguide0205-2 (1 pages) appguide0206 (1 pages) appguide0207 (1 pages) appguide0304 (1 pages) |
Check in e-portals |
World-H-News Products Extensions Partners Automation Jet Parts |
| Sitemap Folder | group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder |
