| Outline | Product Index RF/IF Bluetooth Devices 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers 0587 RFid, Readers Shielding |
| Content | More Product Available Online: www.digikey.com Toll-Free: 1-800-344-4539 • Phone 218-681-6674 • Fax: 218-681-3380586 (US2011) B Accessories ID ISC.ANT.PS-B is a 3dB power splitter with galvanic isolation between the input and the two outputs. At the operating frequency of 13.56MHz the impedance on all in and outputs is calibrated to 50Ω. Both outputs are internally wired in parallel. The galvanic isolation can be enabled by means of two jumpers. The device is designed for installation indoors or outdoors. The connection cable from the Reader to the ID ISC.ANT.PS-B is 3.6m in length. This extends the overall cable length from Reader to antenna to a total of 7.20m. Specifi cations: • Housing: Plastic Polycarbonate (light white) • Dimensions (W x H x D): 130mm x 94mm x 57mm ±2mm • Weight: Approximately 275g • Enclosure Rating: IP 65 • Cable Fittings: 4 x Cable Fitting M16 x 1.5 • Voltage Supply: 12 ~ 24VDC (optional) • Power Consumption: Maximum 4W • Operating Frequency: 13.56MHz • RF Connections: 1 x Input and 2 x Output: SMA Jack (50Ω) (Maximum tightening torque: 0.45Nm) • SWR: Maximum 1.2:1 (50Ω) • Input Loss: Maximum 0.6dB • Temperature Range: Operating: -25°C ~ 55°C; Storage: -40°C ~ 85°C • Flame Proof: UL1950, HB without Cable 629-1005-ND (FEIG ELECTRONICS # 1269.003.01) .$418.02 ID ISC.ANT.PS-B The 8 times Multiplexer ID ISC.ANT.MUX facilitates switching between RFID antennas with an operating frequency of 13.56MHz. With one Multiplexer several single antennas and gate solutions (existing of base and complementary antennas) can be operated with only one reader. Any of the eight Multiplexers outputs can be assigned to both inputs by jumper adjustment. The Multiplexer is controlled either via a digital input or the antenna cable connected with the reader. Specifications: • Dimensions (L x W x H): 182mm x 110mm x 90mm • Weight: Approximately 550g • Protection Class: IP 65 • Grommet: 12x screwed cable gland M16 x 1.5 • Power Supply: 12-24VDC • Power Consumption: Maximum 4W • Operating Frequency: 13.56MHz • Ab sorbability per Channel: Maximum 0.5dB • Maximum Allowed Switching Capacity: 10W • RF Connections: 2x Input: SMA Socket (50Ω); 8x Output: SMA Socket (50Ω) • RF Switch: Switching rate: Electronic switch, <1ms • Triggering: Reader: via RF input 1; External pulse generator: digital input • Digital Inputs: 1 Opto coupler input, maximum 24VDC/20mA • Display: 1x LED per channel, 3x LED (Run/HF/communication) • Tem perature Range: Operating: -25°C ~ 65°C; Storage: -40°C ~ 80°C 629-1040-ND (FEIG ELECTRONICS # 1977.000.01) .$1282.74 ID ISC.ANT.MUX EasyBee™ Transceivers EasyBee is an IEEE 802.15.4 compliant RF transceiver. It enables designers to easily add ZigBee / IEEE 802.15.4 wireless capability to their products without the need for RF or antenna design expertise. The module contains all RF circuitry, including integral antenna and controller in a simple-to-use, plug-in or surface mount module. A 4-wire SPI port interfaces to a baseband microcontroller. The PHY (Physical) layer includes an impedance matched balun and integral antenna. The MAC (Media Access Control) layer includes CRC-16 generation, clear channel assessment, signal energy detection, security, encryption and authentication. It is a fully capable device and a ZigBee networking layer is not required for point-to-point communication. This module is an application-ready solution for fast-to-market ZigBee and IEEE 802.15.4 communications, providing the development engineer unlimited choice of host controller and stack fi rmware provider Features: • Free space range approximately 120m • FCC/CE compliant • Integral antenna • Output power 1mW / 0dBm • Consumes just 20mA (Rx), 18mA (Tx) • 2.1V ~ 3.6V supply 658-1000-5-ND (FlexiPanel # EASYBEE-DIL) .$32.06 658-1001-5-ND (FlexiPanel # EASYBEE-S0) .$20.41 Pixie™ Transceivers Pixie™ Evaluation Kit The Pixie Evaluation Kit is designed for research and development with FlexiPanel Ltd’s Pixie ZigBee modules. Features: • 4 switch inputs • 4 pushbutton inputs • 8 LED outputs • 1 trimmer input • ICD2 programming socket • Solder pads for custom development 658-1012-ND (FlexiPanel # EVAL-PIXIE) .$356.25 658-1002-5-ND (FlexiPanel # PIXIE-DIL-PXSC) .$52.56 658-1003-5-ND (FlexiPanel # PIXIE-DIL-PXSR) .$52.56 658-1004-5-ND (FlexiPanel # PIXIE-SO-PXSC) .$40.01 658-1005-5-ND (FlexiPanel # PIXIE-SO-PXSR) .$40.01 658-1006-5-ND (FlexiPanel # PIXLITE-DIL-PLFE) .$51.27 658-1007-5-ND (FlexiPanel # PIXLITE-DIL-PLSE) .$51.27 658-1008-5-ND (FlexiPanel # PIXLITE-SO-PLFE).$36.83 658-1009-5-ND (FlexiPanel # PIXLITE-SO-PLSE) .$36.83 Pixie provides a complete ZigBee solution for OEMs, integrating IEEE 802.15.4 2.4GHz PHY/MAC layers with Microchip Technology’s NWK/APL/ZDO layers. It provides a path for extremely rapid migration from Microchip’s PICDEM Z ZigBee development environment to market-ready product. It is capable of full function device (FFD) operation and is suitable for router and coordinator nodes. The lower cost Pixie Lite version is used for reduced function devices, e.g. endpoints, with 2 fewer I/O lines and being 3mm more compact. Features: • Free space range approximately 120m • FCC/CE/IC compliant • MAC address allocation • Signature G antenna, low “hand effect” design • Output power 1mW / 0dBm • Consumes less than 25mA when active, 2µA in sleep mode • 15 general I/O lines, 10-bit A/D, serial UART, 4 Interrupts, counter input • Master SPI • 2.1V ~ 3.6V supply With the help of these tuning boards, you can realize your own individual antenna arrays, combined with our i-scan Long Range readers. The dynamic antenna tuner ID ISC.DAT-A is designed for automatic calibrating and tuning of RFID antennas with an operating frequency of 13.56MHz. The parameters for setting the antenna are measured on the board under operating conditions. The antenna tuner is also able to disconnect the antenna circuit through an electronic switch up to a certain power. The ID ISC.DAT is driven over the HF line. The antenna tuner thus functions as a so-called function unit. Measured parameters or the calibration status can be sent to the host over the HF line. Dynamic Antenna Tuning Board. Specifi cations: • Di- mensions (W x H x D): 118mm x 90mm x 19mm • Weight: Approximately 100g • Supply Voltage: 7 ~ 12VDC • Current Consumption: Maximum 150mA (DC) • Operating Frequency: 13.56MHz • Maximum Transmitting Power: 10W • Antenna Switch: Electronic Switch • Antenna Connection: Cable Terminals d = 2 ~ 9mm • RF Connection: SMA Male (50Ω) • Triggering: Reader, Communication via RF-Connection • Outputs: 3 x Open Collector: 5VDC/maximum 15mA • Signal Indicator: 1 x “RUN”-LED • Interface: RS232 TTL (for Firmware Update) • Carrier Frequency: 13.56MHz • Impedance: 50Ω • Tuning Range Inductance: 0.7 ~ 2.5µH • Quality: 10 ~ 50 • Temperature Range: Operating: -25°C ~ 75°C; Storage: -40°C ~ 80°C 629-1006-ND (FEIG ELECTRONICS # 1269.005.01) .$996.30 ID ISC.DAT-A Battery Charger 2560.00.00 is a specifi c for PRH101-B readers only. This unit is suitable to charge the four AA NiCd or NiMH needed to operate the PRH-1001-B. Capacity range of 800mAh to 7200mAh. Features: • Mains indicator • Charging indicator • Trickle charge indicator • Wrong polarity protection • Discharge indicator • Dimensions (L x W x H) 118mm x 62mm x 48mm • CE, CSA, GS and SAA 629-1052-ND (FEIG ELECTRONICS # 2650.000.00) .$122.66 This ID CAB.NET.24V-B-US is an AC power cord that is used with the ID NET.24V-B power supply unit. It uses a U.S. style, AC male plug on one end and a computer style female connector to the power supply unit on the other. 629-1051-ND (FEIG ELECTRONICS # 2560.000.00) .$9.87 The ID CAB.RS-A is a communication cable for RS-232/RS-485 interfaces. It is used with ID ISC.MR101-A, ID ISC.PR101-A, ID ISC.MR101.M-A and ID ISC.PR101.M-A reader products. The cable uses a 9-pin Sub D male on one end and a 9-pin Sub D female with a DC jack spliced on the other end. 629-1028-ND (FEIG ELECTRONICS # 1690.000.00) .$27.89 ID CAB.NET.24V-B-US ID CAB.RS-A ID ISC.ANT.C2-A and ID ISC.ANT.C6-A is a coaxial cable with male SMA style plug connectors on both ends. The cable is used with ID ISC.ANT.U250/250 UHF antennas. 629-1023-ND (FEIG ELECTRONICS # 1654.002.00) 2 Meter Cable .$78.06 629-1024-ND (FEIG ELECTRONICS # 1654.003.00) 6 Meter Cable .$95.26 ID ISC.ANT.C2-A and ID ISC.ANT.C6-A ID ISC.ANT.C-A is a 1/4 Lambda @ 13.56MHz, 3.6 meter, RG58 C/U, coaxial cable with male SMA style plug connectors on both ends. The cable is used with ID ISC.DAT-A Dynamic Antenna Tuning Boards. 629-1042-ND (FEIG ELECTRONICS # 2096.000.00) .$63.40 ID ISC.ANT.C-A ID ISC.ANT.EC is a 1/2 Lambda, 7.2 meter, RG58 C/U, coaxial cable with one male SMA style plug connector on one end and one SMA female in-line splice connector on the other. The cable is used as an antenna extension cable when used with ID ISC.DAT-A Dynamic Antenna Tuning Boards, ID ISC.ANT300/300 antenna, ID ISC.ANT800/600-DA antenna, and ID ISC.ANT1400/760-A/B/C gate antennas. 629-1021-ND (FEIG ELECTRONICS # 1654.000.00) .$66.76 ID ISC.ANT.EC ID ISC.MS.MR/PR-A is a mounting set that attach to the back of our mid-range (MR) or proximity range (PR) readers. 629-1029-ND (FEIG ELECTRONICS # 1691.000.01) .$36.16 ID ISC.MS.MR/PR-A The ID CAB.A-A is a short adapter cable that converts a 10-pin molex style connector through a ribbon cable to a 9-pin Sub D female connector. It is used with ISC.M02 and CPR.M02 reader modules 629-1047-ND (FEIG ELECTRONICS # 2259.000.00) .$20.87 ID CAB.A-A ISC.LR.I/O-A Specifi cations: • Dimensions: (W x H x D) 40mm x 100mm x 10mm • Weight: Approximately 40g • Relays: 3x normally open (contact load capacity: 24VAC/DC 2A) • Inputs: 3 optocoupler (Maximum 24VDC / 20mA) • Temperature Range: Operating: -25°C ~ 60°C; Storage: -40°C ~ 85°C • Relative Humidity: 95% (non- condensing) Items: • 1 – ID ISC.LR.I/O-A Extension Board • 2 – Hex standoffs M3 x 15 metal • 1 – Hex standoffs M3 x 15 plastic • 1 – Recessed raised fi llister head screw M3 x 6 • 1 – Cable 3-conductor (1:1) • 1 – Cable 2-conductor (2 to 5 conductor) • 1 – Ribbon cable 20-conductor • 10 – Jumpers 629-1055-ND (FEIG ELECTRONICS # 2673.000.01) .$129.05 Antennas (Cont.) The UHF antenna ID ISC.ANT.U250/250-FCC are circular polarized antenna for operating frequencies in the UHF range 902-928MHz (FCC antenna). Transponders can be identifi ed in two different orientations (E plane / H plane). Specifi cations: • Housing: Plastic • Dimensions (W x H x D): 260mm x 260mm x 56mm • Weight: Approximately 1050g • Color: White (similar RAL9018) • Protection Class: IP 54 • Operating Frequency: FCC antenna, 902MHz ~ 928MHz • Gain: FCC antenna, 8.7dBic @ 915MHz • 3dB Beam Width: E plain: 65°; H plain: 65° • Polarization: Circular • VSWR: <1.5:1 • Antenna Connection: SMA socket (50Ω) • Temperature Range: Operating: -25°C ~ 55°C; Storage: -25°C ~ 85°C 629-1009-ND (FEIG ELECTRONICS # 1451.009.02) .$339.40 OBID i-scan mid range antennas are operated in combination with mid range reader ID ISC.MR100-x. Depending on the application, pad or industrial antennas may be used. The elegant Pad Antenna ID ISC. ANT340/240 is perfectly suitable for desk applications with a reading range of up to 30cm. File and document tracking as well as the registration of rental goods during distribution and return are only two out of many possible applications. For applications in rough industrial environments with a required range of up to 40cm, we recommend antenna type ID ISC.ANT300/300. Specifications: • Housing: Plastic ABS • Color: Grey- white • Dimensions (W x H x D): 337mm x 237mm x 8.3mm • Weight: 530g • Protection Class: IP 40 • Ad missible Transmitting Power: 1W • Reading Distance: Up to 30cm • Antenna Connection: SMA - plug (50Ω) • Antenna Cable: RG174 (2.0m) • Operating Frequency: 13.56MHz • Temperature Range: Operating: 0°C ~ 55°C; Storage: -25°C ~ 85°C 629-1025-ND (FEIG ELECTRONICS # 1663.000.00) .$256.42 ID ISC.ANT40/30-A • External 50Ω antenna for ID ISC.M02 • Dimensions: 40mm x 30mm • Cable: Coax cable approximately 50cm in length 629-1038-ND (FEIG ELECTRONICS # 1967.000.00) .$75.83 ID ISC.ANT.U250/250-FCC ID ISC.ANT340/240 ID ISC.ANT40/30-A |