Specifications | Manual for the MKS Instruments T3P Pendulum Valve with an RS-232 Interface T3P Valve RS-232 Manual t3p, t3pi, t3pia MKS Instruments |
Business section |

Specifications | Manual for the MKS Instruments T3P Pendulum Valve with an RS-232 Interface T3P Valve RS-232 Manual t3p, t3pi, t3pia MKS Instruments |
Business section |
Specifications | Manual for the MKS Instruments T3P Pendulum Valve with an RS-232 Interface T3P Valve RS-232 Manual t3p, t3pi, t3pia MKS Instruments |
Suggested Link Details/Purchase | |
Content | Chapter Three: Product Overview Control Mode 26 LEARN Function The purpose of the LEARN function is to obtain the chamber pump speed versus valve position using the real operating conditions of sensor type, chamber volume, inlet flow, and pumping system. The LEARN function should be executed prior to normal valve operation. The LEARN function is generally required only once during initial setup/installation. The sequence of steps required to LEARN the valve is as follows: 1. Enter the chamber volume in liters utilizing the valve software interface. An approximate value for volume may be used provided the volume estimator is turned on (see the following step). 2. Determine appropriate setting for the volume estimator: a. If you are confident of the actual chamber volume entered, turn off the volume estimator. b. If you are unsure of the actual chamber volume, turn on the volume estimator. The volume estimator will determine the volume during the system learn and use this volume for pressure control. 3. Set correct pressure transducer ranges. Refer to the MKS Type T3B/T3P Valves with RS-232 Interface Supplement, as necessary. 4. Obtain the recommended learn flow setting from the valve software. 5. Turn on flow to the desired rate for the duration of the LEARN test. 6. Enter the actual flow rate that is being used. 7. Start the LEARN function. The flow rate should remain constant until the LEARN function is completed. The LEARN function moves the valve over a set of non-uniformly distributed positions and records the pressure data from the valve high channel transducer. The typical duration of the LEARN function execution is less than 45 seconds. The pressure data versus time resembles Figure 5. If the actual flow is significantly lower than the recommended flow (dotted line), the accuracy of the obtained chamber pump speed may be insufficient. If the actual flow is much higher than the recommended flow (dashed line), the pressure transducer saturation may occur. This will result in incorrect pump speed curve and will negatively affect the quality of pressure control. Adjust the flow, if necessary, and rerun the system learn starting with Step 5 above. |
Navigation | Previous Page / Next Page |
Following Datasheets | T3Pds (4 pages) T3PIA-DIM (4 pages) T6244R7 (4 pages) T64000 (8 pages) T6822r1-1 (3 pages) T7418 (3 pages) T95-1 (2 pages) Tabell1_2006_slutv_Energivet (1 pages) Tabell2_2006_06_l_r_stud_energivet (1 pages) Table_1_1 (1 pages) |
Check in e-portals![]() |
World-H-News Products Extensions Partners Automation Jet Parts |
Sitemap Folder | group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder |