| Specifications | Microsoft Word - T100102952_Inst_Man_ Rev A.docx gobbi_a |
| Business section |
|
|
|
|
|
||||||||||||||||||||||||||||||||||
|
|
|
|
|
||||||||||||||||||||||||||||||||||
| Specifications | Microsoft Word - T100102952_Inst_Man_ Rev A.docx gobbi_a |
| Business section |
| Specifications | Microsoft Word - T100102952_Inst_Man_ Rev A.docx gobbi_a |
| Suggested Link Details/Purchase | |
| Content | T100102952_A 18 SPS4453-LF connector location (For refernce) Remote user Interface Connect the RJ-045 cables to the remote user interface, one cable for the SPS4450-LF version and two cables for the SPS4450-1-LF version, taking care to ensure cables connect to corresponding connectors at each end, A to A and B to B. 6. Operating the system Charge the Battery Module When the Power Supply Module is plugged into a live AC wall outlet, it will automatically charge the Battery Module. The LED display will continue to strobe from left to right, even if the batteries are fully charged, to indicate AC input power is applied. Battery Modules continuously left in a discharged state will suffer a permanent loss of capacity. CAUTION! The Power Supply Module must be plugged into a live AC utility wall outlet for a minimum of 3.5 hours after installation to fully charge the batteries. If the Power Supply Module is plugged in and turned on, any connected equipment will receive AC power. However, connected equipment may not receive full battery backup runtime when the Power Supply is mobile (disconnected from an AC outlet) until the BBU is fully charged. Plug AC Equipment to be powered into the Power Supply Module’s Outlets The Power Supply Module provides filtered, pure sine-wave 120VAC power for a variety of equipment, including computers, monitors, diagnostic devices, scanners and more. Connected equipment power must be maintained at less than 250W in order not to exceed the Power Supply’s rated capacity.* * To determine any connected equipment VA rating, look on its nameplate. If the equipment is rated in amps, multiply the number of amps by 120 to determine the equivalent watts. Battery Power Battery Sense Program |
| Navigation | Previous Page / Next Page |
| Following Datasheets | T155_420_-_550_kV_Gas-insulated_Substations_Brochure_GB (8 pages) T200_for_Website (4 pages) T2X_E_ALL_PAGES_v514red2 (12 pages) T300MVi_Ethernet_Interface_V1_100_Manual (69 pages) T3b-T3P-DeviceNetSupplement-MAN (130 pages) T3b-T3P-RS232Supplement-MAN (59 pages) T3Bds (4 pages) T3BI-DIM (1 pages) T3BIB-DS (4 pages) T3P-AnalogTTL-MAN (70 pages) |
Check in e-portals |
World-H-News Products Extensions Partners Automation Jet Parts |
| Sitemap Folder | group1 group2 group3 group4 group5 group6 group7 group8 group9 group10 group11 group12 group13 group14 group15 group16 group17 group18 group19 group20 group21 group22 group23 group24 group25 group26 group27 group28 group29 group30 group31 group32 group33 group34 group35 group36 group37 group38 group39 group40 group41 group42 group43 group44 group45 group46 group47 group48 group49 group50 group51 group52 group53 group54 group55 group56 group57 group58 group59 group60 group61 group62 group63 group64 group65 group66 group67 group68 group69 group70 group71 group72 group73 group74 group75 group76 group77 group78 group79 group80 group81 group82 group83 group84 group85 group86 group87 group88 group89 group90 group91 group92 group93 group94 group95 group96 group97 group98 group99 group100 Prewious Folder Next Folder |
